The latest news and products from Midland Helicopters

Published: 18th May, 2012 at 12:48 pm

Align T-Rex 600DFC Main Shaft for the 600ESP

Align T-Rex 600DFC Main Shaft for 600ESP

Align T-Rex 600DFC Main Shaft for 600ESP

This main shaft is only for T-Rex 600ESP model to fit with 600DFC head.

Please do not use it on other models and purposes.

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 12:45 pm

Align T-Rex 450 Plus Spares starting to appear

Align T-Rex 450 Plus Spares

Align T-Rex 450 Plus Spares

We have added the currently available spares for the T-Rex 450 Plus (Ready To Fly) to our website in their own new category.

To view these model specific parts, please click here.

Published: 18th May, 2012 at 12:35 pm

Align 450 Pro 4mm Motor Mount

Align 450 Pro 4mm Motor Mount

Align 450 Pro 4mm Motor Mount

Here we have an extra thick and extra strong motor mount for the Align T-Rex 450 Pro.

The standard motor mount is a bit on the thin side, and can be bent quite easily, in a crash. Save yourself the hassle of replacing the motor mount time after time and fit one of these instead!

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 12:32 pm

Scorpion HK4525 Motor Shaft Kit

Scorpion HK4525 Motor Shaft Kit

Scorpion HK4525 Motor Shaft Kit

The Scorpion HK-4525 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a “Less than Perfect” landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4525 series Scorpion Helicopter Motors.

The shaft for the HK-4525 series motors measures 10mm in diameter, and is 91.5mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 12:27 pm

Swashplate Leveling Tool V2 – Various sizes

Swashplate Leveling Tool V2

Swashplate Leveling Tool V2

Here we  have a lovely range of swashplate levelling tools. The clean finish and great design make these tools a joy to use.

They are available for several models, so please click the relevent link(s) for your model(s) below.

Swashplate Leveling Tool V2 – MSH Protos 500

Swashplate Leveling Tool V2 – LOGO 500/600

Swashplate Leveling Tool V2 – Align T-Rex 450 Pro/Sport

Swashplate Leveling Tool V2 – Align T-Rex 500

Swashplate Leveling Tool V2 – Align T-Rex 550/600

Swashplate Leveling Tool V2 – Align T-Rex 700

Published: 18th May, 2012 at 12:11 pm

iPitch Gauge

iPitch Gauge

iPitch Gauge

Are you looking for a smart, easy to use pitch gauge? This could be it!

This is the iPitch Gauge, which is a holder for your iPhone. You attach it to your rotorblade, then fit your iPhone to it and you then can use an inclinometer app on your iphone to set up your blade pitch! Fantastic!

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 12:06 pm

Engine Bearing Tool Set – 60/91

Engine Bearing Tool Set - 60/91

Engine Bearing Tool Set - 60/91

The easy way to remove front and rear engine bearings from your 60 to 91 size engines (should also work with 105/120 engines as well) without heating the engine up.

The process on how to use the tool is covered in the video attached to the product, and also after the break on this article. Please click through to watch, but mind your ears on the music!

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 11:55 am

Engine Bearing Tool Set – 50/56

Engine Bearing Tool Set - 50/56

Engine Bearing Tool Set - 50/56

The easy way to remove front and rear engine bearings from your 50 to 56 size engines without heating the engine up.

The process on how to use the tool is covered in the video attached to the product, and also after the break on this article. Please click through to watch, but mind your ears on the music!

Click here to view the product and to buy yours.

Published: 18th May, 2012 at 11:51 am

Two-way Fine Adjustable Linkage Rods (Turnbuckles)

Two-way Fine Adjustable Linkage Rods

Two-way Fine Adjustable Linkage Rods

Usually, we can’t fine-tune a typical ball linkage set to any length because we need to turn the ball link a whole turn, or at least half a turn, in order to keep the direction of the ball link. Besides, we need to take off and put on the ball link for adjustment everytime and this can be a pain!

Now this problem is solved.

With the two-way fine adjustable linkage rods (also known as turnbuckles), you are able to fine-tune the linkage length without taking off the ball link.

We have several sizes and rod thicknesses available, along with sets that come with the adjustment tool or just the rods on their own. Please click the links below to view that product.

Two-way Fine Adjustable Linkage Rods w/tool M2 x 34mm

Two-way Fine Adjustable Linkage Rods M2 x 34mm

Two-way Fine Adjustable Linkage Rods w/tool M2 x 48mm

Two-way Fine Adjustable Linkage Rods M2 x 48mm

Two-way Fine Adjustable Linkage Rods w/tool M2 x 56mm

Two-way Fine Adjustable Linkage Rods M2 x 56mm

Two-way Fine Adjustable Link Rods w/Tool M2.5x71MM

Two-way Fine Adjustable Linkage Rods M2.5 x 71MM

 

Published: 18th May, 2012 at 11:39 am

Universal Swashplate Levelling Tool

Universal Swashplate Levelling Tool

Universal Swashplate Levelling Tool

This is the ultimate design of Universal Swashplate Leveling Tool.

It fits 99% of any type of swashplate on the market, no matter which type (90, 120, 135 or 140), shaft size (3, 3.5, 5, 8, 10 or 12mm) or size (200~700 or more).

Comes with the required shaft size adaptors, ready to go!

Click here to view the product and to buy yours.

Subscribe to our eNewsletter

Stay up to date with the latest happenings with our free eNewsletter! Includes exclusive eNewsletter only special offers. Don't miss out... subscribe today!

Midland Helicopters eNewsletter subscription form
* = required field